1 ftr-k1 series ?? features ? ? 2 poles, 2 form c ? ? contact gap: more than 0.6mm ? ? high surge voltage: 2500v between open contacts 5000v between coil & contact complies with telcordia (former bellcore) 2nd level surge ? ? dielectric strength: 1500vac between open contacts 3000vac between coil and contact ? ? dimensions of large contact gap relay height: 9.3mm maximum (tht) 9.65mm maximum (smt) length: 15mm maximum width: 7.5mm maximum ? ? conforms to iec60950/ en60950/ul1950/csa c 22.2 no. 950 working voltage 250v (supplementary) ? ? high insulation: clearance: min 2.0mm (coil and contacts) creepage: min 2.5mm (coil and contacts) ? ? high reliability-bifurcated contacts ? ? low power consumption 280mw (latching type 140mw) ? ? rohs compliant actual marking does not carry the type name : "ftr" e.g.: ordering code: ftr-c1ca012g actual marking: c1ca012g power relay 2 poles-2a high insulation/wide gap ftr-c1 series (a) relay type ftr-c1 : ftr-c1 series (b) contact con guration c : through hole type g : surface mount type s : surface mount type reduced mounting area (c) coil type / enclosure a : standard type b : single coil latching type (d) coil rated voltage 012 : 3....24vdc coil rating table at page 3 (e) contact material g : gold plated silver palladium (f) tape / reel ordering nil : standard packaging (tube) b05 : tape / reel package, only available for smt type ?? partnumber information ftr-c1 c a 012 g - b05 [example] (a) (b) (c) (d) (e) (f )
2 ftr-k1 series ?? specification item non-latching ftr-c1 ( ) a latching ftr-c1 ( ) b contact data con guration 2 form c construction bifurcated material gold plated silver palladium resistance (initial) max. 100mohm at 1a, 6vdc contact rating resistive 1a, 30vdc / 0.3a, 125vac / 0.3a, 110vdc max. switching voltage 250vac / 220vdc max. switching power 62.5va / 30w max. carry current 2a min. switching load * 10ma, 10mvdc life mechanical min. 2 x 10 6 operations electrical min. 100 x 10 3 operations at 0.3a, 125vac / 1a, 30vd coil data rated power 280 to 300mw 140 to 180mw operate power 158 to 162mw 158 to 162mw operating temp range -40 to +85c (no frost) timing data operate (at nominal voltage) max. 6ms (without bounce) release (at nominal voltage) max. 6ms (without bounce) insulation resistance (initial) min. 1,000mohm at 500vdc dielectric strength open contacts 1500vac (50/60hz) 1min strength contacts to coil 3,000vac (50/60hz) 1min surge strength coil to contacts 5,000v, 1.2 x 10 s standard wave/6,000v, 1.2 x 50 s clearance open contacts 0.6mm clearance adjacent contacts 1.0mm clearance coil and contacts 2.0mm creepage open contacts 0.6mm creepage coil and contacts 2.5mm creepage adjacent contacts 1.0mm other vibration resistance misoperation>1us 10 to 55hz double amplitude 3.3mm endurance 10 to 55hz double amplitude 5mm shock misoperation>1us min. 500m/s 2 endurance min. 1,000m/s 2 weight approximately 2g * minimum switching loads mentioned above are reference values. please perform the con rmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. ftr-c1 series
3 ftr-k1 series ?? coil rating coil code rated coil voltage (vdc) coil resistance +/- 10% (ohm) must operate voltage (vdc) * must release- voltage (vdc) * max. coil voltage (vdc) nominal coil power (mw) 003 3 32.1 2.25 0.3 4.5 280 4.5 4.5 72.3 3.38 0.45 6.75 005 5 89.3 3.75 0.5 7.5 012 12 514 9 1.2 18 024 24 1,920 18 2.4 36 300 note: all values in the table are valid for 20c and zero contact current. * speci ed operate values are valid for pulse wave voltage. type compliance contact rating ul ul 508 e63615 flammability: ul 94-v0 (plastics) 0.3a, 125 vac (resistive) 1 a, 30vdc 0.3a, 110vdc csa c22.2 no. 14 lr 40304 bsi iec 60950-1 ?? safety standards ftr-c1 series standard type coil code rated coil voltage (vdc) coil resistance +/- 10% (ohm) set voltage (vdc) * reset voltage (vdc) * max. coil voltage (vdc) nominal coil power (mw) 003 3 64.0 +2.25 - 2.25 4.5 140 4.5 4.5 145 +3.38 - 3.38 6.75 005 5 179 +3.75 - 3.75 7.5 012 12 1,029 +9 - 9 18 024 24 3,200 +18 - 18 36 180 latching type
4 ftr-k1 series ?? characteristic data ftr-c1 series
5 ftr-k1 series ftr-c1 series ? dimensions and schematics through hole type ? terminal designations ? recommended mounting pad unit: mm unit: mm s shows the polarity of set position r shows the polarity of reset position standard type (bottom view de-energized position) single coil latching type (bottom view reset position)
6 ftr-k1 series ftr-c1 series ? dimensions and schematics surface mount type unit: mm (bottom view de-energized position) ? terminal designations standard type s shows the polarity of set position r shows the polarity of reset position single coil latching type (bottom view reset position) ? recommended mounting pad unit: mm
7 ftr-k1 series ftr-c1 series ? dimensions and schematics space saving type unit: mm single coil latching type (bottom view reset position) ? recommended mounting pad ? terminal designations bottom view de-energized position s shows the polarity of set position r shows the polarity of reset position
8 ftr-k1 series ftr-c1 series ? recommended soldering conditions smt note: 1.temperature pro les show the temperature of pc board surface. 2. please perform soldering test with your actual pc board before mass production, since the temperatures of pc board surfaces vary according to the size of pc board, status of parts mounting and heating method. ? packaging reel dimensions: unit: mm packaging method (only tape packaging is available) 1. taping standards: jis c 0806 and rc-10092b (eiaj) 2. tape type: tb2416 or te2416 3. reel type: rd24d 4. quantity of 1 reel: 500 pieces tape dimensions: (temperature profile, please see page 9)
9 ftr-k1 series 1. general information ? all signal and power relays produced by fujitsu components are compliant with rohs directive 2002/95ec including amendments. ? cadmium as used in electrical contacts is exempted from the rohs directives on october 21st, 2005. (amendment to directive 2002/95/ec) ? all of our signal and power relays are lead-free. please refer to lead-free status info for older date codes at: http://www.fujitsu.com/us/downloads/micro/fcai/relays/lead-free-letter.pdf ? lead free solder plating on relay terminals is sn-3.0ag-0.5cu, unless otherwise speci ed. this material has been veri ed to be compatible with pbsn assembly process. 2. recommended lead free solder pro le ? recommended solder sn-3.0ag-0.5cu. rohs compliance and lead free information 3. moisture sensitivity ? moisture sensitivity level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. tin whiskers ? dipped snagcu solder is known as presenting a low risk to tin whisker development. no considerable length whisker was found by our in house test. we highly recommend that you con rm your actual solder conditions flow solder condition: pre-heating: maximum 120 ? c soldering: dip within 5 sec. at 260 ? c solder bath solder by soldering iron: soldering iron temperature: maximum 360 ? c duration: maximum 3 sec. ftr-c1 series re ow solder condition for smt
10 ftr-k1 series japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia paci c fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ fujitsu components international headquarter of ces ?2011 fujitsu components europe b.v. all rights reserved. all trademarks or registered trademarks are the property of their re spective owners. the contents, data and information in this datasheet are provided by fujitsu component ltd. as a service only to its user and o nly for gen- eral information purposes. the use of the contents, data and information provided in this datasheet is at the users? own risk. fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen- sive, complete and up to date. fujitsu components europe b.v. and af liated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data , and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness t hereof. nor do fujitsu components europe b.v. and af liated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantab ility or tness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, rel iability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. rev. february 18, 2011 ftr-c1 series
|
